Eye protection at work: safety glasses, full-view glasses and face shields
Eye protection protects against particles, dust, splashes and optical radiation at work. At A+S Technigro, you will find over 50 models from Bollé, 3M, PIP Global Safety, COFRA and Helmut Feldtmann: Safety glasses, Goggles as well as Face shields and welding helmets. In addition, there are Eye protection accessories such as eyewash bottles and lens cleaning products.
The general requirements for safety glasses and face protection are set out in DIN EN ISO 16321-1:2026-06. It replaces, among others, DIN EN 166:2002-04 and the filter standards DIN EN 170:2003-01 and DIN EN 172:2002-02. What eye protection is required is determined by your company's risk assessment.

Which hazard requires which eye protection
The appropriate design depends on the hazards at the workplace:
- Flying particles during assembly, drilling and order picking: safety glasses with side protection.
- Dust, grinding particles and liquid splashes: full-view safety glasses that fit tightly against the face.
- Splashes and splinters that can hit the entire face: face shields.
- Welding: welding filters according to DIN EN ISO 16321-2:2026-06, for example in automatic welding helmets.
- Outdoor work: tinted lenses with a sun protection filter, also polarized for reflections on water or wet surfaces.
What to check before purchasing
- Marking: according to DIN EN ISO 16321-1:2026-06 or, for older certificates, according to DIN EN 166:2002-04, on the lens and frame.
- Lens tint: clear for indoor use, yellow for increased contrast, grey or brown for sun protection, indoor/outdoor lenses when moving between the warehouse and the yard.
- Coating: K for scratch resistance, N to prevent fogging.
- Combination: fit when worn with hearing protection, respiratory protection or a helmet.
- Vision correction: glasses wearers need overglasses or prescription safety glasses.
From DIN EN 166 to DIN EN ISO 16321: what changes in marking
The DIN EN ISO 16321 standard series is available in German as the 2026-06 edition. Part 1 contains the general requirements, Part 2 the requirements for welding, and Part 3 the requirements for fabric protective equipment such as welding screens. DIN EN 166:2002-04 has been withdrawn. According to manufacturer information, existing EN 166 certificates remain valid until they expire, for a maximum of five years. Both markings are therefore available side by side in the product range, for example with the Bollé Swift according to EN ISO 16321-1 and the Bollé Contour according to EN 166.
The most important changes in marking are:
- Impact resistance: C stands for 45 m/s (formerly F), E for 120 m/s (formerly B); D for 80 m/s is new. The former class A is no longer used.
- Temperature: A T after the letter, e.g. CT, indicates testing at minus 5 and plus 55 degrees Celsius.
- Filters: UV filters are marked with a U instead of 2, sun protection filters with a G instead of 5, and welding filters with a W.
- New markings: 6 for liquid streams, 7 for radiant heat, and CH for chemical resistance.
- Head sizes: Testing is carried out on six test heads; if a pair of glasses does not fit the medium head size, the size is marked.
What the individual symbols mean is explained in the Safety glasses marking guide and the encyclopedia under EN ISO 16321. The difference in designs is described in the entry Full-view glasses or temple glasses. You can find protective clothing for welding under Welding protection.

Organizing eye protection in the workplace
Eye protection only works if it is worn. For businesses, this means:
- Issue personally: According to Section 2 of the German PPE Ordinance (PSA-BV), PPE is generally intended for one person and must fit them individually.
- Keep overglasses available for visitors and external contractors, such as the 3M Visitor 2700.
- Replace scratched or damaged lenses.
- Keep an eyewash station close at hand in case of splashing hazards.
The employer bears the costs: According to Section 3 (3) of the German Occupational Safety and Health Act (ArbSchG), they may not pass on the costs of occupational safety measures to employees. For regular supplies, the B2B registration is worth it.
Questions about eye protection
Who bears the cost of safety glasses and corrective safety glasses?
Who bears the cost of safety glasses and corrective safety glasses?
The employer, because under Section 3 (3) of the Occupational Safety and Health Act, employees may not be charged for the costs of occupational safety measures. If the risk assessment shows that eye protection is necessary, this also applies to employees with visual impairments; they may require prescription safety glasses. According to DGUV Rule 112-192 (February 2006 edition), overglasses are generally only suitable for short-duration tasks. For Bollé prescription safety glasses, the Seamless Vision voucher is available.
Can safety glasses with EN 166 continue to be used?
Can safety glasses with EN 166 continue to be used?
Yes. Although the DIN EN 166:2002-04 standard has been withdrawn, according to the manufacturer, existing certificates remain valid until they expire, for a maximum of five years. New certifications are carried out according to DIN EN ISO 16321-1:2026-06. Whether glasses can continue to be worn depends on their condition.
Are regular sunglasses or prescription glasses considered eye protection?
Are regular sunglasses or prescription glasses considered eye protection?
No. Under Section 2 of the PPE Regulation, employers may only provide protective equipment that complies with Regulation (EU) 2016/425. Everyday glasses do not meet these requirements and bear no occupational safety marking.
What does G2 or 5-2.5 mean on tinted safety glasses?
What does G2 or 5-2.5 mean on tinted safety glasses?
Both indicate a sun protection filter for outdoor work. 5-2.5 is the old designation according to DIN EN 172:2002-02, G2 is the new one according to DIN EN ISO 16321-1:2026-06. For glare, there are polarized models such as the Bollé Tryon TRYOPOL.
What eye protection is required for welding?
What eye protection is required for welding?
For welding, DIN EN ISO 16321-2:2026-06 applies. It replaces, among others, DIN EN 169:2003-02, DIN EN 175:1997-08 and DIN EN 379:2009-07. In our range, you will find, for example, the Bollé Fusion+ Automatic Welding Helmet and a Welding Flip-Up Glasses. The required protection level depends on the process and the current.
Weiterführende Links und Quellen
Quellen
- DIN Media: DIN EN ISO 16321-1:2026-06 (abgerufen am 15.11.2026)
- DIN Media: DIN EN ISO 16321-2:2026-06 (abgerufen am 15.11.2026)
- DIN Media: DIN EN ISO 16321-3:2026-06 (abgerufen am 15.11.2026)
- DGUV Regel 112-192 Benutzung von Augen- und Gesichtsschutz, Ausgabe Februar 2006 (abgerufen am 15.11.2026)
- Arbeitsschutzgesetz, § 3 (abgerufen am 15.11.2026)
- PSA-Benutzungsverordnung, § 2 (abgerufen am 15.11.2026)
- KomNet NRW: Korrektionsschutzbrillen und Überbrillen (abgerufen am 15.11.2026)
- uvex: Umstellung von EN 166 auf EN ISO 16321 (abgerufen am 15.11.2026)
- Herstellerangaben in den Produktdaten (abgerufen am 15.11.2026)
Die Auswahl der Schutzausrüstung richtet sich nach der Gefährdungsbeurteilung Ihres Unternehmens.


