Cut-resistant gloves: Protection against blades, edges and sheet metal
Cut-resistant gloves protect the hands when working with knives, sharp-edged sheet metal, glass or stamping parts. They are tested according to DIN EN 388:2019-03, the German version of EN 388:2016+A1:2018 for protective gloves against mechanical risks. The decisive factor for cut protection is the test according to EN ISO 13997:1999 with the cut protection levels A to F: A stands for a cutting force of 2 Newtons or more, F for at least 30 Newtons.
In our range you will find over 70 cut-resistant gloves, including those from Ejendals (Tegera), MAPA, LEBON, Ansell and ATG, from thin models for fine work up to level F. Which level is required is determined by your company's risk assessment. For activities without a significant cut risk, assembly gloves are suitable; you can find the entire selection under work and protective gloves.

Where cut protection is needed
Cut-resistant gloves are used anywhere hands handle or guide sharp workpieces: in sheet metal and metalworking, glass cutting, automotive manufacturing, opening packages in the warehouse, and working with knives.
What to check before purchasing
- Cut resistance level: the letter A to F in the fifth position of the marking according to EN 388.
- Coating: Nitrile, polyurethane, or latex improve grip; coatings with oil grip are designed for oily parts.
- Dexterity: The finer the work, the thinner the glove should be.
- Additional protection: Impact protection (P), heat protection according to DIN EN 407:2020-06, or forearm cut protection.
- Food contact: only models with the glass fork symbol or the note "for food contact".
- Size: according to hand circumference and hand length according to EN ISO 21420.
Marking according to EN 388 step by step
Under the EN 388 pictogram are four digits and one or two letters, for example 4 X 4 3 D. Each position represents a separate test:
- 1st position: Abrasion resistance, levels 0 to 4
- 2nd position: Cut resistance in the coupe test, levels 0 to 5; an X means not tested or not applicable
- 3rd position: Tear resistance, levels 0 to 4
- 4th position: Puncture resistance, levels 0 to 4
- 5th position: Cut protection according to EN ISO 13997:1999, levels A to F
- 6th position: P if the optional impact protection has been passed, for example with the EXONIT 853
The coupe test and testing according to EN ISO 13997 cannot be converted into one another. Therefore, always compare gloves based on the same test, usually based on the letter. The glossary explains all levels under EN 388.
An important limitation: According to DGUV rule 112-195, wearing protective gloves when using drills is prohibited because the glove can be caught by rotating parts. When working with a circular saw, a glove can also increase the risk. For heat at the workplace, you will find heat protection gloves, for heavy-duty work without cut risk leather gloves.

How to find the right glove
Choosing the right level involves balancing protection and dexterity. This approach has proven effective:
- Identify workplace hazards: blades, edges, weight, and surface of the parts.
- Determine the cut protection level and coating.
- Have several samples worn in actual operations and involve the employees.
- Establish a replacement interval; replace damaged gloves immediately.
Read more options in the guide Choosing Protective Gloves Correctly.
Questions about cut-resistant gloves
What cut protection level do I need?
What cut protection level do I need?
This is determined by the risk assessment. The levels A to F according to DIN EN 388:2019-03 stand for cut forces of 2, 5, 10, 15, 22 and 30 Newtons. Higher levels offer better protection but are often thicker. A trial with several samples shows which model best combines protection and dexterity.
What does the X in the second position of the marking mean?
What does the X in the second position of the marking mean?
The X indicates that the coupe test was not performed or is not applicable. This is the case with many cut-resistant gloves because high-performance fibers can dull the blade in the coupe test. The decisive factor is then the letter in the fifth position, for example D in 4 X 4 3 D.
Can I wear cut-resistant gloves while using the drill?
Can I wear cut-resistant gloves while using the drill?
No. According to DGUV Rule 112-195, wearing protective gloves when using drills is prohibited because the glove can be caught and the hand pulled in. This also applies to cut-resistant gloves.
Are cut-resistant gloves suitable for food?
Are cut-resistant gloves suitable for food?
Only if the manufacturer states that they are suitable for that purpose. According to Article 15 of Regulation (EC) No 1935/2004, you can identify this by the glass and fork symbol or the indication “for food contact”. In our range, this applies, for example, to several Ansell HyFlex and Tegera Infinity models; this information is provided in the product data.
What does the P mean in the marking?
What does the P mean in the marking?
P stands for passing the impact protection test according to EN 388. Such gloves have protectors on the back of the hand and are suitable for work where the hand may also be crushed or struck.
Weiterführende Links und Quellen
Quellen
- DIN Media: DIN EN 388:2019-03, Schutzhandschuhe gegen mechanische Risiken (abgerufen am 15.11.2026)
- DGUV Regel 112-195: Benutzung von Schutzhandschuhen, Ausgabe April 1994, aktualisierte Nachdruckfassung Oktober 2007 (abgerufen am 15.11.2026)
- BG ETEM: impuls 2/2020 (abgerufen am 15.11.2026)
- IHK München: Merkblatt Lebensmittelbedarfsgegenstände, Januar 2025, zu Verordnung (EG) Nr. 1935/2004 (abgerufen am 15.11.2026)
- Herstellerangaben in den Produktdaten (abgerufen am 15.11.2026)
Die Auswahl der Schutzausrüstung richtet sich nach der Gefährdungsbeurteilung Ihres Unternehmens.


