Select protective gloves and work gloves suitable for the hazard
Protective gloves are part of personal protective equipment and protect the hands from mechanical, chemical and thermal hazards. The right glove is determined by your company's risk assessment: sharp edges, oils, cleaning agents, hot parts or cold each place different demands on the material and level of protection.
In this category you will find over 300 work gloves and protective gloves, including from Ejendals (TEGERA), MAPA, Ansell, Hase Safety Gloves, Wonder Grip and Mechanix Wear. All protective gloves are subject to the basic standard DIN EN ISO 21420:2024-11, which sets requirements for fit, dexterity and marking; the level of protection against individual hazards is governed by separate standards, such as DIN EN 388:2019-03 for mechanical risks. The basics are explained in the glossary under EN ISO 21420.

What types of protective gloves are there?
The product range is categorized by protective function:
- Assembly gloves: Grip and dexterity for assembly, warehousing and manual work, tested according to DIN EN 388:2019-03.
- Cut-resistant gloves: for sheet metal, glass and knives; the cut resistance rating from A to F indicates the result of the TDM test.
- Chemical protective gloves: for acids, alkalis and solvents, classified according to DIN EN ISO 374-1:2018-10 as Type A, B or C.
- Disposable gloves: for short-term tasks in laboratories, cleaning and food processing.
- Cold protection gloves: for outdoor work and refrigerated areas, tested according to DIN EN 511:2006-07.
- Heat protection gloves: for hot surfaces and contact heat, tested according to DIN EN 407:2020-06.
Sorted by material, you will also find leather gloves, knitted gloves, nitrile gloves, latex gloves, chloro-/neoprene gloves and butyl-/viton gloves.
Correctly reading the markings on protective gloves
Each protective glove features pictograms indicating performance levels. The higher the number or letter, the better the glove performed in the respective test. The most important markings:
- Mechanical risks according to DIN EN 388:2019-03: four digits for abrasion resistance, cut resistance in the couteau test, tear resistance, and puncture resistance, plus a letter A to F for cut protection according to the TDM test and, if applicable, a P for impact protection. Details in the glossary under EN 388.
- Chemicals according to DIN EN ISO 374-1:2018-10: Type A, B, or C indicates how many test chemicals the glove is resistant to and for how long; the identifying letters indicate the substances tested. More under EN ISO 374.
- Heat according to DIN EN 407:2020-06: six levels, including flammability, contact heat, and radiant heat. More under EN 407.
- Cold according to DIN EN 511:2006-07: three levels for convective cold, contact cold, and water resistance. More under EN 511.
An overview of all pictograms is provided in the guide Classifications of Protective Gloves.
A glove only protects when it is worn. Gloves that are too large reduce grip and dexterity, while gloves that are too small fatigue the hand. Sizes 6 to 11 are defined in DIN EN ISO 21420:2024-11 according to hand circumference and hand length; size 8 corresponds to a hand circumference of approximately 20 cm, for example. During prolonged wear, cotton liners and regular changes help relieve the skin when using liquid-tight gloves.

Protective gloves by area of use
The gloves needed in your business depend on the workplace:
- Construction and trades: durable assembly and leather gloves with a good grip, suitable for the Roofers & Carpenters section.
- Production and metalwork: cut and heat protection, find out more under Production & Manufacturing.
- Cold and outdoor work: lined cold-weather gloves, complemented by Winter Workwear.
- Cleaning, laboratory and chemical work: chemical protection and disposable gloves.
Questions about work and protective gloves
When are protective gloves mandatory at work?
When are protective gloves mandatory at work?
Protective gloves are required if the risk assessment identifies risks to the hands that cannot be eliminated through technical or organizational measures. This is how the STOP principle provides: Personal protective equipment is only used after these measures.
Who pays for protective gloves?
Who pays for protective gloves?
The employer. Under Section 3(3) of the Occupational Safety and Health Act, the employer may not pass on the costs of occupational safety measures to the employees. This also includes the protective equipment that must be provided in accordance with the Personal Protective Equipment at Work Ordinance.
Which glove size is right?
Which glove size is right?
Measure the circumference of the hand without the thumb and the length from the wrist to the tip of the middle finger. According to DIN EN ISO 21420:2024-11, a circumference of around 18 cm corresponds to size 7, 20 cm to size 8, 23 cm to size 9, and 25 cm to size 10. The size is indicated on each glove.
Are there gloves that protect against multiple hazards?
Are there gloves that protect against multiple hazards?
Yes. According to the manufacturer, the Ansell AlphaTec 58-201 is tested to EN 388:2016+A1:2018, EN 407:2020, EN 511:2006 and EN ISO 374-1:2016, meaning it protects against mechanical risks, contact heat, cold and chemicals. The MAPA TempIce 700 combines protection according to EN 388:2016 with cold and wet protection according to EN 511:2006. The pictograms on the respective model are decisive.
Why do hands sweat in protective gloves, and what helps?
Why do hands sweat in protective gloves, and what helps?
Liquid-tight gloves do not allow sweat to escape, and prolonged wear can cause the skin to become macerated. Change the gloves regularly, wear cotton liners if necessary, and specify in the skin protection plan which protective and care products should be used before and after work.
When should protective gloves be replaced?
When should protective gloves be replaced?
Replace gloves if they are punctured, torn, hardened, or swollen, and after contact with substances for which they have not been tested. For chemical protective gloves, the wear time specified by the manufacturer must be observed; if an expiry date is given, this must also be observed.
Weiterführende Links und Quellen
Quellen
- DIN Media: DIN EN ISO 21420:2024-11, Schutzhandschuhe, Allgemeine Anforderungen und Prüfverfahren (abgerufen am 15.11.2026)
- DIN Media: DIN EN 388:2019-03, Schutzhandschuhe gegen mechanische Risiken (abgerufen am 15.11.2026)
- DIN Media: DIN EN ISO 374-1:2018-10, Schutzhandschuhe gegen gefährliche Chemikalien und Mikroorganismen (abgerufen am 15.11.2026)
- DIN Media: DIN EN 407:2020-06, Schutzhandschuhe gegen thermische Risiken (abgerufen am 15.11.2026)
- DIN Media: DIN EN 511:2006-07, Schutzhandschuhe gegen Kälte (abgerufen am 15.11.2026)
- DGUV Regel 112-195: Benutzung von Schutzhandschuhen (abgerufen am 15.11.2026)
- Arbeitsschutzgesetz, § 3 (abgerufen am 15.11.2026)
- Herstellerangaben in den Produktdaten (abgerufen am 15.11.2026)
Die Auswahl der Schutzausrüstung richtet sich nach der Gefährdungsbeurteilung Ihres Unternehmens.


